free templates joomla

Super Team

Intake Manifolds & Accessories

TF III Int Man 3-4 ft left view nbr  300 x 262TF III Int Man top ft view nbr  300 x 308

 

Top Fuel Stage III Intake Manifolds

25A-103-000

Top Fuel Stg III Magnesium Intake Manifold, 10.725” Std Deck height, Revised 2015 Set Back design. AJ Top opening & Top relief, .210" O-ring, 1/2" Blower Studs. Uses 2ea Round Stg III Burst Panels front & rear, and 2 ea Stg II / Small Rectangular burst panels on top of front cyl runners. Manifolds come drilled with 1/8” NPT holes on both ends for pan pressure transducer. (each)

 

TF Intake Man Hardware nbr 300 x 198

 

Top Fuel Stg III Intake Manifold Parts

25A-110-TF-KIT

Stg I, II + III T/F Intake Manifold Stud and Nut Kit. Includes: 6ea studs + nuts. (kit)

25A-110-TF

Stud, 3/8 NC x 3.800" OAL, for Top Fuel Stg I, II+ III Intake Manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25A-140-TF-18-SQ

Intake Oil Fill Plug, -18AN Thread w/ 1/2" Female Square drive. Standard for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

25A-145-TF-18-HEX

Intake Oil Fill Plug, -18AN Thread w/ 3/4" Male Hex. Optional for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

23Z-030-018

O-Ring #126B, For Top Fuel -18 AN Intake Manifold Oil Filler Plug. .103" x .1362" I.D. x 1.568" O.D. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

TF III B-P Parts nbr 300 x 263TF III B-P Block Off Plate nbr  125 x 123

 

Top Fuel Stg III Burst Panels, Etc: Large Round Burst Panels

25Z-300-BP

Stg III Burst Panel, 4.5" dia. Round w/ 12 holes. SFI certified. (each)

25Z-300-BP-20PK

Stg III Burst Panel, 4.5" dia. Round w/ 12 holes. SFI certified. (Discounted to $19.75ea in 20 packs)(20 pack)

25Z-300-GASKET

Gasket, TF Stg III Burst Panel Adapter Ring. Round 4.200" od with 12 holes. Used between B-P Adapter Ring & Intake Manifold. (pair)

25Z-050-KIT-10

Burst Panel Stud & Nut Kit, for T/F Stg III round burst panel, REV D style. Includes 10ea studs + nuts. (kit)

25Z-050-KIT-20

Burst Panel Stud & Nut Kit, for T/F Stg III round burst panel, REV D style. Front & rear kit includes 20ea studs + nuts. (kit)

25Z-310-KIT-REV-D

T/F Stg III Front Burst Panel Adapter Ring Kit. Includes 12ea Screws, 10ea Studs & Nuts, 2ea Dowel Pins + 1ea O-ring. (kit)

25Z-310-REV-D

T/F Stg III Burst Panel Adapter Ring, Front. .500" thick. Used w/ V-Band Clamp & 10ea studs. (B-P adapter ring w/ 2ea dowel pins, does not include any Screws / Studs / O-ring) (ea)

25Z-310-KIT

T/F Stg III Front Burst Panel Adapter Ring Kit. Includes 12ea Screws, 12ea Dowel pins + 1ea O-ring. (kit)

25Z-310

T/F Stg III Burst Panel Adapter Ring, Front. .500" thick. (B-P adapter ring w/ dowel pins only, does not use screws)(each)

25Z-310-R-KIT-REV-D

T/F Stg III Rear Burst Panel Adapter Ring Kit. Includes: 12ea Screws, 10ea Studs + Nuts, 2ea Dowel Pins + 1ea O-ring. (kit)

25Z-310-R-REV-D

T/F Stg III Burst Panel Adapter Ring, Rear. .500" thick. Used w/ V-Band Clamp & 10ea studs. (B-P adapter ring includes 2ea dowel pins, does not include any screws. studs or O-ring)(each)

25Z-310-R-KIT

T/F Stg III Rear Burst Panel Adapter Ring Kit. Includes 12ea Screws, 12ea Dowel pins + 1ea O-ring. (kit)

25Z-310-R

T/F Stg III Burst Panel Adapter Ring, Rear. .500" thick. (B-P adapter ring used w/ dowel pins only, does not use screws)(each)

25Z-315-REV-D

T/F Stg III Burst Panel Retainer Ring, .290" thick. Used with 10 Studs & Nuts & V-Band Clamp, when not using a B-P deflector. (B-P retaining ring only, no hardware) (each)

25Z-315

T/F Stg III Burst Panel Retainer Ring, .290" thick. Used with V-Band Clamp only, when not using a B-P deflector. (B-P retaining ring only, no hardware)(each)

25Z-320-ALUM

Band Clamp, Aluminum V-Band, for T/F Stg III Burst Panel Adapter Ring (each)

25Z-320-SS

Band Clamp, Stainless Steel V-Band, for T/F Stg III Burst Panel Adapter Ring (each)

25Z-350

Stg III TF Burst Panel Deflector, AJPE Elbow style, Black anodized. Use with V-Band Clamps. (Does not include band clamp or burst panel)(each)

25Z-350-REV-D

Stg III TF Burst Panel Deflector, AJPE Elbow style, Black. Can use with v-band clamp &/or Stud + Nut kit #25Z-050-KIT-12.(Does not include hardware or burst panel)(each)

25Z-370-046

O-Ring, T/F Stg III Burst Panel Adapter: #046 .070" x 4.239" I.D. x 4.379" O.D. (each)

 

Int Manifold Channels nbr  300 x 129

 

Top Fuel Hemi Int Manifold Channels & Related Parts

25A-002

TFX Hemi TF Intake Manifold End Seal Channel Kit. Includes: 2ea channels & 8 screws. Note: fits TFX blocks only! Std & +.100" tall Deck. (kit)

25A-003

TF Hemi Intake Manifold End Seal Channel only, Std & +.100" Deck blocks. Note: fits TFX block end rails only! (each)

00Z-FHCS-1024-0500

10-24 x 1/2 Flat Head Cap Screw, for the TF intake manifold end rail channels. (each)

 

 

TF II Int Man nbr  300 x 213 

 

 

Top Fuel Stage II Intake Manifolds

Note: due to NHRA rules changes, when our current inventory of TF Stg II Intake Manifolds is depleted

AJPE will no longer manufacture any more of this style manifolds. Please call AJPE for more information.

25A-102-000

Top Fuel Stg II 426 Hemi Magnesium Intake Manifold, 10.725” Std Deck height. (aka: Set Back Manifold). AJ Top opening & Top relief, .210" O-ring, 7/16" Blower Studs. Uses 2ea Small Stg III rectangular burst panels. (each)

25A-102-100

Top Fuel Stg II 426 Hemi Mag Intake Manifold, +.100" Tall Deck. (aka: Set Back Manifold) AJ Top opening & Top relief, .210" O-ring, 7/16" Blower Studs. Uses 2ea Small Stg II rectangular burst panels. (each)

 

 

TF Intake Man Hardware nbr 300 x 198

Top Fuel Stg II Intake Manifold Parts

25A-110-TF-KIT

Stg I, II + III T/F Intake Manifold Stud and Nut Kit. Includes: 6ea studs + nuts. (kit)

25A-110-TF

Stud, 3/8 NC x 3.800" OAL, for Top Fuel Stg I, II+ III Intake Manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25A-140-TF-18-SQ

Intake Oil Fill Plug, -18AN Thread w/ 1/2" Female Square drive. Standard for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

25A-145-TF-18-HEX

Intake Oil Fill Plug, -18AN Thread w/ 3/4" Male Hex. Optional for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

23Z-030-018

O-Ring #126B, For Top Fuel -18 AN Intake Manifold Oil Filler Plug. .103" x .1362" I.D. x 1.568" O.D. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

 

 

Stg II B-P etc  nbr 300 x 158TF II B-P Block Off Plate nbr 170 x 96

 

 

TF Stg II Burst Panels, Etc: Small Rectangular Burst Panels

25Z-200-BP

Stg II / Small Burst Panel, SFI Certified. (18 holes)(net $, no discount)(each)

25Z-200-GASKET

Stg II / Small Burst Panel Gaskets, 2 pack. (18 holes) (pair)

25Z-210-KIT-NBP

Stg II Burst Panel Frame Kit, Includes Outer B-P frame & 18ea 10-24 x 5/8" BHCS Screws. (Does not include BP) (kit)

25Z-210-KIT-WBP

Stg II Burst Panel Kit w/ BP. Includes: Stg II B-P frame kit and + Stg II BP. (kit)

25Z-210

Stg II Outer Burst Panel Frame only. Does not include Screws or BP. (each)

25Z-210-SCREW-KIT

Stg II Burst Panel Screw Kit, Includes 18ea 10-24 x 5/8" BHCS. (kit)

25Z-220-KIT

Stg II Burst Panel Block Off Plate Kit, Includes 18ea 10-24 x 5/8" BHCS. (kit)

25Z-220

Stg II Burst Panel Block Off Plate only. Does not include Screws. (each)

00Z-BHCS-1024-0625

10-24 x 5/8" Button Head Cap Screw (each)

25Z-050-KIT-18

Burst Panel Stud & Nut Kit, for T/F Stg II small rectangular burst panel. Includes 18ea studs + nuts. (kit)

 

Int Manifold Channels nbr  300 x 129

 

Top Fuel Hemi Int Manifold Channels & Related Parts

25A-002

TFX Hemi TF Intake Manifold End Seal Channel Kit. Includes: 2ea channels & 8 screws. Note: fits TFX blocks only! Std & +.100" tall Deck. (kit)

25A-003

TF Hemi Intake Manifold End Seal Channel only, Std & +.100" Deck blocks. Note: fits TFX block end rails only! (each)

00Z-FHCS-1024-0500

10-24 x 1/2 Flat Head Cap Screw, for the TF intake manifold end rail channels. (each)

 

TF Stg I Nost Int Man  nbr  300 x 211

 

Top Fuel Stage I Intake Manifolds

25A-001-000

Top Fuel Stg I 426 Hemi Magnesium Intake Manifold, 10.725” Std Deck height. (Non-set back style). Includes stud & nut kit. Must specify: BP location & Top opening, Blower stud threads, etc. Uses Large Stg I rectangular burst panel. 2.250" wide x 2.185" tall port openings. (each)

25A-001-100

Top Fuel Stg I 426 Hemi Magnesium Intake Manifold, +.100" Tall Deck height, Complete. (Non-set back style). Includes stud & nut kit. Must specify: BP location, Top opening, Blower stud threads, etc. Uses Large Stg I rectangular burst panel. 2.250" wide x 2.185" tall port openings. (each)

25A-001-500S

Top Fuel Stg I 426 Hemi Magnesium Intake Manifold, -.500" Short Deck, Complete. (Non-set back style). Includes stud & nut kit. Must specify: BP location, Top opening, Blower stud threads, etc. Uses Large Stg I rectangular burst panel. 2.250" wide x 2.185" tall port openings. (each)

 

TF Intake Man Hardware nbr 300 x 198

 

Top Fuel Stg I Intake Manifold Parts

25A-110-TF-KIT

Stg I, II + III T/F Intake Manifold Stud and Nut Kit. Includes: 6ea studs + nuts. (kit)

25A-110-TF

Stud, 3/8 NC x 3.800" OAL, for Top Fuel Stg I, II+ III Intake Manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25A-140-TF-18-SQ

Intake Oil Fill Plug, -18AN Thread w/ 1/2" Female Square drive. Standard for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

25A-145-TF-18-HEX

Intake Oil Fill Plug, -18AN Thread w/ 3/4" Male Hex. Optional for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

23Z-030-018

O-Ring #126B, For Top Fuel -18 AN Intake Manifold Oil Filler Plug. .103" x .1362" I.D. x 1.568" O.D. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

Int Manifold Channels nbr  300 x 129

 

Top Fuel Hemi Int Manifold Channels & Related Parts

25A-002

TFX Hemi TF Intake Manifold End Seal Channel Kit. Includes: 2ea channels & 8 screws. Note: fits TFX blocks only! Std & +.100" tall Deck. (kit)

25A-003

TF Hemi Intake Manifold End Seal Channel only, Std & +.100" Deck blocks. Note: fits TFX block end rails only! (each)

00Z-FHCS-1024-0500

10-24 x 1/2 Flat Head Cap Screw, for the TF intake manifold end rail channels. (each)

 

TF Stg I Nost Int Man  nbr  300 x 211

 

Nostalgia 426 Top Fuel Intake Manifolds

25A-001-NOST-000

Nostalgia TF Stg I 426 Hemi Magnesium Intake Manifold, 10.725” Std Deck height. "Small port" Nostalgia style. Includes stud & nut kit. Must specify: BP location & Top opening. 2.010" wide x 1.820" tall port openings. (each)

25A-001-NOST-100

Nostalgia TF Stg I 426 Hemi Magnesium Intake Manifold, +.100" Tall Deck height. "Small port" Nostalgia style. Includes stud & nut kit. Must specify: BP location & Top opening. 2.010" wide x 1.820" tall port openings. (each)

25A-001-NOST-500S

Nostalgia TF Stg I 426 Hemi Magnesium Intake Manifold, -.500" Short Deck. "Small port" Nostalgia style. Includes stud & nut kit. Must specify: BP location * Top opening. 2.010" wide x 1.820" tall port openings. (each)

 

TF Intake Man Hardware nbr 300 x 198

 

Nostalgia 426 Top Fuel Intake Manifold Parts

25A-110-TF-KIT

Stg I, II + III T/F Intake Manifold Stud and Nut Kit. Includes: 6ea studs + nuts. (kit)

25A-110-TF

Stud, 3/8 NC x 3.800" OAL, for Top Fuel Stg I, II+ III Intake Manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25A-140-TF-18-SQ

Intake Oil Fill Plug, -18AN Thread w/ 1/2" Female Square drive. Standard for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

25A-145-TF-18-HEX

Intake Oil Fill Plug, -18AN Thread w/ 3/4" Male Hex. Optional for TF + 5300 Manifolds only. Includes O-ring. (Not for M-H manifolds)(each)

23Z-030-018

O-Ring #126B, For Top Fuel -18 AN Intake Manifold Oil Filler Plug. .103" x .1362" I.D. x 1.568" O.D. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

Int Manifold Channels nbr  300 x 129

 

Top Fuel Hemi Int Manifold Channels & Related Parts

25A-002

TFX Hemi TF Intake Manifold End Seal Channel Kit. Includes: 2ea channels & 8 screws. Note: fits TFX blocks only! Std & +.100" tall Deck. (kit)

25A-003

TF Hemi Intake Manifold End Seal Channel only, Std & +.100" Deck blocks. Note: fits TFX block end rails only! (each)

00Z-FHCS-1024-0500

10-24 x 1/2 Flat Head Cap Screw, for the TF intake manifold end rail channels. (each)

 

MH Int Man nbr  300 x 161

 

Muscle Head Hemi Intake Manifolds

25A-300-000

Muscle Head Hemi Magnesium Intake Manifold. Std 10.725” deck height, front burst panel opening. Must specify top opening & O-ring. (each)

25A-300-100

Muscle Head Hemi Magnesium Intake Manifold. +.100" Tall 10.825” deck height, front burst panel opening. Must specify top opening & O-ring. (each)

25A-300-500S

Muscle Head Hemi Magnesium Intake Manifold. -.500" Short 10.225” deck height, front burst panel opening. Must specify top opening & O-ring. (each)

 

TF Intake Man Hardware nbr 300 x 198

 

Muscle Head Hemi Intake Manifold Parts

25A-310-MH-KIT

Muscle Head Hemi TAD / TAFC / PM Intake Manifold Stud & Nut Kit. Std Deck & +.100" Tall Deck manifolds only. Includes 10ea 3.250" OAL studs + nuts. (kit)

25A-310-MH-KIT-500S

Muscle Head Hemi TAD / TAFC / PM Intake Manifold Stud & Nut Kit. For -.500" Short Deck manifolds only. Includes 10ea 2.937" OAL studs + nuts. (kit)

25A-311-MH-KIT

Muscle Head Hemi A/F Intake Manifold Stud & Nut Kit. Includes 10ea 3.95" OAL studs + nuts. (kit)

25A-310-MH

Stud, 3/8 NC x 3.250" OAL, for Muscle Head Hemi with cast TAD + TA/FC Intake manifolds, Std Deck & +.100" Tall Deck manifolds only. (each)

25H-010

392 & M-H Intake Manifold Stud: 3/8 x 2.937" OAL. 3/8-16 coarse threads both ends, For "3-Bolt" 392 intake manifolds & -.500" Short Deck M-H Hemi intake manifolds. (each)

25A-311-MH

Stud, 3/8 NC x 3.950" OAL, for Muscle Head Hemi with A/Fuel sheet metal intake manifold. Not for cast TAD / TAFC / Pro Mod intake manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25A-340-MH-16

Intake Manifold Oil Fill Plug w/ O-Ring, -16 AN Thread w/ 3/4" Male Hex. For Muscle Head Manifolds only. (Not for T/F intake manifolds)(each)

23Z-030-016

O-Ring #916, For Muscle Head Hemi -16 AN Intake Manifold Oil Filler Plug. .116” x 1.171” I.D. x 1.403” O.D. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

23N-005

5300 Hemi Intake Port O-Ring, #234B. .139" x 2.984" I.D. x 3.262" O.D. Also fits: 481-X Stg III & 5.3 Semi-Hemi. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

   

Int Manifold Channels nbr  300 x 129

 

M-H Hemi Intake Manifold Channels & Related Parts

25A-320-MH-000

MH Hemi Stg II Intake Manifold End Seal Channel / Spacer only, for Std Deck. Note: fits TFX block end rails only! Std deck blocks. Channel / Spacers = .360"/.370" thick. (each)

25A-320-MH-000-KIT

M-H Hemi Stg II Intake Manifold End Seal Channel / Spacer Kit, for Std Deck. Kit includes 2ea Channel/Spacers & 8 screws. Fits TFX block end rails only! Channel / Spacers = .360"/.370" thick.(kit)

25A-320-MH-100

MH Hemi Stg II Intake Manifold End Seal Channel / Spacer only, for +.100” Tall Deck. Note: fits TFX block end rails only! +.100" Tall Deck blocks. Channel / Spacers = .360"/.370" thick. (each)

25A-320-MH-100-KIT

M-H Hemi Stg II Intake Manifold End Seal Channel / Spacer Kit, for +.100" Tall Deck. Kit includes 2ea Channel/Spacers & 8 screws. Fits TFX block end rails only! Channel / Spacers = .360"/.370" thick. (kit)

25A-320-MH-500S

MH Hemi Stg II Intake Manifold End Seal Channel / Spacer only, for -.500” Short Deck. Note: fits TFX block end rails only! Channel / Spacers = .160"/.170" thick.(each)

25A-320-MH-500S-KIT

M-H Hemi Stg II Intake Manifold End Seal Channel / Spacer Kit, for -.500" Short Deck. Kit includes 2ea Channel / Spacers & 8 screws. Fits TFX block end rails only! Channel / Spacers = .160"/.170" thick.(kit)

00Z-FHCS-1024-0500

10-24 x 1/2 Flat Head Cap Screw, for the TF intake manifold end rail channels. (each)

00Z-FHCS-1024-0625

10-24 x 5/8" Flat Head Cap Screw, for the MH II intake manifold end rail channel/spacers. (each)

 

481-X Int Man nbr 300 x 230

 

481-X Stage I & II Intake Manifolds

25B-001-1000

481-X Stg I & II Magnesium Intake Manifold, 10.000" Short Deck. Includes Bolt kit, End seals & Top O-ring cord. Must specify: Top opening, & Front or Rear B-P opening. Stg I & II intake port openings = 2.020” wide x 2.710” tall. (each)

25B-001-1040

481-X Stg I & II Magnesium Intake Manifold, 10.400" Tall Deck. Includes Bolt kit, End seals & Top O-ring cord. Must specify: Top opening, & Front or Rear B-P opening. Stg I & II intake port openings = 2.020” wide x 2.710” tall. (each)

 

 Int Man Hdwre nbr  300 x 167

 

481-X Stg I & II Intake Manifold Parts

25B-010-KIT

481-X Intake Manifold Bolt & Washer kit (kit)

00Z-030-2250

3/8-16 x 2-1/4" 12pt Bolt, Gold. (each)

00Z-080-06

3/8 AN Washer, Gold. (each)

23Z-005

Intake Port O-Ring, #232B. .139" x 2.734" I.D. x 3.012" O.D. For T/F Hemi, M-H Hemi, 5300 Hemi & 481-X Stg I+II, etc. (each)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

481-X Int Man nbr 300 x 230

 

481-X Stage III & IV Intake Manifolds

25B-003-1000-III

481-X Stg III & IV Magnesium Intake Manifold, 10.00" Short Deck. Includes Bolt kit, End seals & Top O-ring cord. Must specify: Top opening, & Front or Rear B-P opening. Stg III & IV intake port openings = 2.210” wide x 2.710” tall. (each)

25B-003-1040-III

481-X Stg III & IV Magnesium Intake Manifold, 10.400" Tall Deck. Includes Bolt kit, End seals & Top O-ring cord. Must specify: Top opening, & Front or Rear B-P opening. Stg III & IV intake port openings = 2.210” wide x 2.710” tall. (each)

 

Int Man Hdwre nbr  300 x 167 

 

481-X Stg III & IV Intake Manifold Parts

25B-010-KIT

481-X Intake Manifold Bolt & Washer kit. (kit)

00Z-030-2250

3/8-16 x 2-1/4" 12pt Bolt, Gold. (each)

00Z-080-06

3/8 AN Washer, Gold. (each)

23N-005

5300 Hemi Intake Port O-Ring, #234B. .139" x 2.984" I.D. x 3.262" O.D. Also fits: 481-X Stg III & 5.3 Semi-Hemi. (each)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

392 intake manifold 300 x 164

 

392 Hemi Magnesium Intake Manifold

25H-001

392 Hemi Magnesium Intake Manifold, 10.860" Std Deck height. w/ Front BP opening. Includes Top O-Ring cord. Must specify: Blower location & Top opening. (Does not include Stud + Nut kit #25H-010-KIT)(each)

 

Int Man Hdwre nbr  300 x 167 

 

392 Hemi Intake Manifold Parts

25H-010-KIT

392 Intake Manifold Stud & Nut Kit. Includes 6ea 2.937” oal Studs & Nuts. (kit)

25H-010

392 & M-H Intake Manifold Stud: 3/8 x 2.937" oal x 3/8-16 coarse thread both ends, For "3-Bolt" 392 intake manifolds & -.500" Short Deck M-H Hemi manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

23H-001

392 Billet Intake Port O-Ring #231B, .139" x 2.609" I.D. x 2.887" O.D. (each)

 

SBC Billet Int Man nbr 300 x 177

 

SBC Billet Cyl Hds Magnesium Intake Manifolds

25C-001-9000

SBC Magnesium Intake Manifold, 9.00" Std Deck height. Includes End seals & Top O-ring cord. Must specify: Top opening, Front or Rear B-P opening & if Distributor hole is needed. (Does not include Bolt kit #25C-010)(each)

25C-001-9300

SBC Magnesium Intake Manifold, 9.300" Tall Deck Height (+.300” Tall). Includes End seals & Top O-ring cord. Must specify: Top opening, Front or Rear B-P opening & if Distributor hole is needed. (Does not include Bolt kit #25C-010)(ea)

25C-001-9500

SBC Magnesium Intake Manifold, 9.500" Tall Deck Height (+.500” Tall). Includes End seals & Top O-ring cord. Must specify: Top opening, Front or Rear B-P opening & if Distributor hole is needed. (Does not include Bolt kit #25C-010)(ea)

 

Int Man Hdwre nbr  300 x 167 

 

SBC Billet Cyl Hds Mag Intake Manifold Parts

25C-010

SBC Billet Intake Manifold Bolt Kit. Includes 6ea 1.75" and 4ea 2.25" long 12pt bolts + 10ea 3/8” AN washers (kit)

00Z-030-1750

3/8-16 x 1-3/4" 12pt Bolt, Gold. (each)

00Z-030-2250

3/8-16 x 2-1/4" 12pt Bolt, Gold. (each)

00Z-070

3/8" Superwasher, Gold. (each)

23C-006

SBC Billet Intake Port O-Ring, #228B, .139" x 2.234" I.D. x 2.512" O.D. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

BBC Indy Int Man nbr 300 x 218

 

BBC Billet Cyl Heads Indy Intake Manifolds

25J-001-1020

BBC Indy Aluminum Intake Manifold, 10.200" Tall Deck height, front burst panel opening. Must specify: "Big Port" or "Small Port" Cyl heads, Blower location & Top opening. (Does not include bolt kit or B-P frame kit) (each)

25J-001-9800

BBC Indy Intake Manifold, 9.800" Std Deck height, front burst panel opening. Must specify: "Big Port" or "Small Port" Cyl heads, Blower location & Top opening. (Does not include bolt kit or B-P frame kit)(each)

 

Int Man Hdwre nbr  300 x 167 

 

BBC Billet C-H Indy Intake Manifold Parts

25J-010-1020-KIT

BBC Intake Manifold Bolt & Washer Kit, 10.200" Deck ht. Includes 12ea 1.750" long 12pt bolts & 12ea 3/8" AN washers. (kit)

25J-010-9800-KIT

BBC Intake Manifold Bolt & Washer Kit, 9.800" Deck ht. Includes 12ea 1.500" long 12pt bolts & 12ea 3/8" AN washers. (kit)

00Z-030-1500

3/8-16 x 1-1/2" 12pt Bolt, Gold. (each)

00Z-030-1750

3/8-16 x 1-3/4" 12pt Bolt, Gold. (each)

00Z-080-06

3/8 AN Washer, Gold. (each)

23J-001

O-Ring, BBC "Large Port" Intake Port O-Ring #242B. Requires 4 per V-8 engine set + 1 ft. of .139" O-Ring cord #23Z-100-139. (Does not fit the "Small Port” heads)(each)

23J-001-SP

O-Ring, BBC "Small Port" Intake Port O-Ring #240B. Requires 4 per V-8 engine set + 1 ft. of .139" O-Ring cord #23Z-015-139. (Does not fit the "Big Port" heads)(each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

5300 Int man nbr 300 x 151 flipped

 

5300 Hemi Intake Manifolds

25N-001-1000

5300 Hemi V-8 Magnesium Intake Manifold, 10.00" Short Deck height, Front burst panel opening. Must specify: Top opening, ect. (Does not include Bolt kit, Burst panel or B-P frame kit)(each)

25N-001-1040

5300 Hemi V-8 Magnesium Intake Manifold, 10.400" Tall Deck height, Front burst panel opening. Must specify: Top opening, ect. (Does not include Bolt kit, Burst panel or B-P frame kit)(each)

 

Int Man Hdwre nbr  300 x 167 

 

5300 Hemi Intake Manifold Parts

25N-009-KIT

5300 Hemi Intake Manifold Bolt kit. Includes 6ea 2.25" long + 4ea 2.50” long bolts & 10ea 3/8 AN washers. (kit)

00Z-030-2250

3/8-16 x 2-1/4" 12pt Bolt, Gold. (each)

00Z-030-2500

3/8-16 x 2-1/2" 12pt Bolt, Gold. (each)

00Z-080-06

3/8 AN Washer, Gold. (each)

25N-010-KIT

5300 Hemi V-8 Intake Manifold Stud + Nut kit. Includes 6ea 2.937" long + 4ea 3.25" long studs & 10ea nuts. (kit)

25A-310-MH

Stud, 3/8 NC x 3.250" OAL, for Muscle Head Hemi with cast TAD + TA/FC Intake manifolds, Std Deck & +.100" Tall Deck manifolds only. (each)

25H-010

392 & M-H Intake Manifold Stud: 3/8 x 2.937" oal x 3/8-16 coarse thread both ends, For "3-Bolt" 392 intake manifolds & -.500" Short Deck M-H Hemi manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

25N-020-KIT

5300 Hemi Intake Manifold End Seal Channel Kit. Fits 10.400" deck height blocks. Includes 2ea channels & 8ea screws. (kit)

25N-020

5300 Hemi Intake Manifold End Seal Channel only. For 10.400" deck height Blocks. (Does not include any hardware)(each)

23N-005

5300 Hemi Intake Port O-Ring, #234B. .139" x 2.984" I.D. x 3.262" O.D. Also fits: 481-X Stg III & 5.3 Semi-Hemi. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

5300 Int man nbr 300 x 151

 

5.3 Semi-Hemi Intake Manifolds

25K-001

5.3" Semi-Hemi V-8 Magnesium Intake Manifold, Front burst panel opening. Must specify: Top opening, ect. (Does not include Bolt Kit, Burst panel or B-P frame kit)(each)

 

Int Man Hdwre nbr  300 x 167 

 

5.3 Semi-Hemi Intake Manifold Parts

25N-009-KIT

5300 Hemi Intake Manifold Bolt kit. Includes 6ea 2.25" long + 4ea 2.50” long bolts & 10ea 3/8 AN washers. (kit)

00Z-030-2250

3/8-16 x 2-1/4" 12pt Bolt, Gold. (each)

00Z-030-2500

3/8-16 x 2-1/2" 12pt Bolt, Gold. (each)

00Z-080-06

3/8 AN Washer, Gold. (each)

25N-010-KIT

5300 Hemi V-8 Intake Manifold Stud + Nut kit. Includes 6ea 2.937" long + 4ea 3.25" long studs & 10ea nuts. (kit)

25A-310-MH

Stud, 3/8 NC x 3.250" OAL, for Muscle Head Hemi with cast TAD + TA/FC Intake manifolds, Std Deck & +.100" Tall Deck manifolds only. (each)

25H-010

392 & M-H Intake Manifold Stud: 3/8 x 2.937" oal x 3/8-16 coarse thread both ends, For "3-Bolt" 392 intake manifolds & -.500" Short Deck M-H Hemi manifolds. (each)

00Z-011

3/8" NC 6pt. Nut with flange, for Hemi Intake Manifold Studs. (each)

23N-005

5300 Hemi Intake Port O-Ring, #234B. .139" x 2.984" I.D. x 3.262" O.D. Also fits: 481-X Stg III & 5.3 Semi-Hemi. (each)

23Z-100-139

.139" Dia Buna N O-Ring Cord material, use for Alky Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

23Z-100-210

.210" Dia Buna N O-Ring Cord material, use for T/F Intake manifold top O-Ring. (confirm dia & length needed)(sold per foot)

24Z-010

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per foot)

24Z-010-10

Intake Manifold End Seal Material, .290"/.312" thick x .500" wide Black closed cell foam (sold per 10 foot roll)

 

 

 

SBC 12o Intake Manifold Spacers

25C-100-0875

AJPE 12* Intake Manifold Spacer Plates, .875" Thick. (pair)

25C-100-1000

AJPE 12* Intake Manifold Spacer Plates, 1.00" Thick. (pair)

 

 

 

 

 

Stg I B-P etc   nbr  300 x 197TF I B-P Block Off Plate nbr  170 x 83

 

Stg I Burst Panels & Related Parts:Large Rectangular Style w/ 24 Holes

25Z-100-BP

Stg I aka Large Burst Panel, SFI Certified. (24 holes)(Net $, no discount)(each)

25Z-100-GASKET

Stg I aka Large Burst Panel Gaskets, 2 pack. (24 holes)(pair)

25Z-050-KIT-24

Burst Panel Stud & Nut Kit, for Stage I aka Large Burst Panel Outer frame. Includes 24ea studs + nuts. (kit)

25Z-050-1024-1000-S

10/24 x 10/32 x 1.00" Stud, for Burst Panel Frames (each)

25Z-050-1032-JETNUT

10/32 Jet Nut, for burst panel studs (each)

25Z-110-OUTER

Stg I Outer Burst Panel Frame Only (Does not include screws or BP)(each)

25Z-110-INNER

Stg I Inner Burst Panel Frame Only. Includes Center screw + Lock nut. If nesc, use with Outer BP frame/kit. (Must use w/ 10-24 x 1" SHCS #25Z-022-100). (each)

25Z-110-IO-KIT-NBP

Stg I Burst Panel Frame Kit. Includes Inner + Outer B-P frames, 24ea 1" long screws, Center screw & Lock nut. (Does not include Burst Panel) (kit)

25Z-110-IO-KIT-WBP

Stg I Burst Panel Frame Kit. Includes Inner + Outer B-P frames, 24ea 1" long screws, Center screw & Loc nut. (Includes Burst Panel)(kit)

25Z-110-O-KIT-NBP

Stg I Outer Burst Panel Frame Kit. Includes Outer B-P frame & screws, center screw & locknut. (Does not include inner BP frame or Burst Panel) (kit)

25Z-110-O-KIT-WBP

Stg I Burst Panel Kit. Includes Outer Burst Panel frame kit & 1ea Stg I Burst Panel. (Does not include inner BP frame)(kit)

25Z-110-SCREW-KIT

Stg I Burst Panel Frame Screw Kit. Includes: 24ea 10-24 x 3/4" SHCS. (set)

25Z-150-KIT

Burst Panel Deflector, DMPE Billet alum "Fish Mouth" style, Black anodized. For Stg I B-P only. Includes mounting screws. (kit)

25Z-150

Burst Panel Deflector, DMPE Billet aluminum "Fish Mouth" style, Black anodized. For Stg I B-P only. (Does not include mounting screws)(each)

25Z-115-PSI-DBL-KIT

Burst Panel Extension Frame Kit, for Double panels on PSI Screw Blowers. For Stg I BP only. Includes mounting screws. (kit)

25Z-115-PSI-DBL

Burst Panel Extension Frame, for Double panels on PSI Screw Blowers. For Stg I BP only. (Does not include mounting screws)(each)

25Z-120-KIT

Stg I Burst Panel Block Off Plate Kit (Includes block off plate + screws)(kit)

25Z-120

Stg I Burst Panel Block Off Plate (Does not include mounting screws)(each)

 

 

 

Stg II B-P etc  nbr 300 x 158TF II B-P Block Off Plate nbr 170 x 96

 

Stg II Burst Panels & Related Parts:Small Rectangular Style w/ 18 Holes

25Z-200-BP

Stg II / Small Burst Panel, SFI Certified. (18 holes)(net $, no discount)(each)

25Z-200-GASKET

Stg II / Small Burst Panel Gaskets, 2 pack. (18 holes) (pair)

25Z-210-KIT-NBP

Stg II Burst Panel Frame Kit, Includes Outer B-P frame & 18ea 10-24 x 5/8" BHCS Screws. (Does not include BP) (kit)

25Z-210-KIT-WBP

Stg II Burst Panel Kit w/ BP. Includes: Stg II B-P frame kit and + Stg II BP. (kit)

25Z-210

Stg II Outer Burst Panel Frame only. Does not include Screws or BP. (each)

25Z-210-SCREW-KIT

Stg II Burst Panel Screw Kit, Includes 18ea 10-24 x 5/8" BHCS. (kit)

00Z-BHCS-1024-0625

10-24 x 5/8" Button Head Cap Screw (each)

25Z-050-KIT-18

Burst Panel Stud & Nut Kit, for T/F Stg II small rectangular burst panel. Includes 18ea studs + nuts. (kit)

 

TF III B-P Parts nbr 300 x 263TF III B-P Block Off Plate nbr  125 x 123

 

TF Stg III Burst Panels & Related Parts:Large Round Style w/ 12 Holes

25Z-300-BP

Stg III Burst Panel, 4.5" dia. Round w/ 12 holes. SFI certified. (each)

25Z-300-BP-20PK

Stg III Burst Panel, 4.5" dia. Round w/ 12 holes. SFI certified. (Discounted to $19.75ea in 20 packs)(20 pack)

25Z-300-GASKET

Gasket, TF Stg III Burst Panel Adapter Ring. Round 4.200" od with 12 holes. Used between B-P Adapter Ring & Intake Manifold. (pair)

25Z-050-KIT-10

Burst Panel Stud & Nut Kit, for T/F Stg III round burst panel, REV D style. Includes 10ea studs + nuts. (kit)

25Z-050-KIT-20

Burst Panel Stud & Nut Kit, for T/F Stg III round burst panel, REV D style. Front & rear kit includes 20ea studs + nuts. (kit)

25Z-310-KIT-REV-D

T/F Stg III Front Burst Panel Adapter Ring Kit. Includes 12ea Screws, 10ea Studs & Nuts, 2ea Dowel Pins + 1ea O-ring. (kit)

25Z-310-REV-D

T/F Stg III Burst Panel Adapter Ring, Front. .500" thick. Used w/ V-Band Clamp & 10ea studs. (B-P adapter ring w/ 2ea dowel pins, does not include any Screws / Studs / O-ring) (ea)

25Z-310-KIT

T/F Stg III Front Burst Panel Adapter Ring Kit. Includes 12ea Screws, 12ea Dowel pins + 1ea O-ring. (kit)

25Z-310

T/F Stg III Burst Panel Adapter Ring, Front. .500" thick. (B-P adapter ring w/ dowel pins only, does not use screws)(each)

25Z-310-R-KIT-REV-D

T/F Stg III Rear Burst Panel Adapter Ring Kit. Includes: 12ea Screws, 10ea Studs + Nuts, 2ea Dowel Pins + 1ea O-ring. (kit)

25Z-310-R-REV-D

T/F Stg III Burst Panel Adapter Ring, Rear. .500" thick. Used w/ V-Band Clamp & 10ea studs. (B-P adapter ring includes 2ea dowel pins, does not include any Screws. Studs or O-ring)(each)

25Z-310-R-KIT

T/F Stg III Rear Burst Panel Adapter Ring Kit. Includes 12ea Screws, 12ea Dowel pins + 1ea O-ring. (kit)

25Z-310-R

T/F Stg III Burst Panel Adapter Ring, Rear. .500" thick. (B-P adapter ring used w/ dowel pins only, does not use screws)(each)

25Z-315-REV-D

T/F Stg III Burst Panel Retainer Ring, .290" thick. Used with 10 Studs & Nuts & V-Band Clamp, when not using a B-P deflector. (B-P retaining ring only, no hardware) (each)

25Z-315

T/F Stg III Burst Panel Retainer Ring, .290" thick. Used with V-Band Clamp only, when not using a B-P deflector. (B-P retaining ring only, no hardware)(each)

25Z-320-ALUM

Band Clamp, Aluminum V-Band, for T/F Stg III Burst Panel Adapter Ring (each)

25Z-320-SS

Band Clamp, Stainless Steel V-Band, for T/F Stg III Burst Panel Adapter Ring (each)

25Z-350

Stg III TF Burst Panel Deflector, AJPE Elbow style, Black anodized. Use with V-Band Clamps. (Does not include band clamp or burst panel)(each)

25Z-350-REV-D

Stg III TF Burst Panel Deflector, AJPE Elbow style, Black. Can use with v-band clamp &/or Stud + Nut kit #25Z-050-KIT-12.(Does not include hardware or burst panel)(each)

25Z-370-046

O-Ring, T/F Stg III Burst Panel Adapter: #046 .070" x 4.239" I.D. x 4.379" O.D. (each)